Whether you have electronic or manual vaping devices, regular maintenance and cleaning is something that is required if you are looking to make sure that each vape session is the best it can be. That said, the approach that you will take to cleaning different devices will vary depending upon what type of product it is, how it is built, and what types of solutions are safe to clean it.
One product that will require you to better understand the device is the nectar collector. Are you the proud owner of your own dab straw or are you looking into getting one soon? If so, here is a comprehensive guide on how you should clean these products so that every hit you take offers you only the smoothest, cleanest vapors.
How to Clean a Nectar Collector
Like it is with most other vape products, the process of cleaning a nectar collector will depend upon what type of nectar collector you have. That said, there are many steps and products that are needed across the board. What will you need to have around in order to make sure that you are always ready to clean your nectar collector when it needs it?
SOAK IT IN ISOPROPYL ALCOHOL
Once you have all of the individual pieces separated, mix the isopropyl alcohol and salt together and either put the solution into a bag or a container. Once you have the evenly-mixed solution ready for your materials, place the body of the nectar collector into the bag, making sure that the solution is able to make its way throughout the entirety of the piece. Most recommend soaking for at least 30 to 60 minutes. However, you can soak your piece for as long as you feel is needed until the residue begins to loosen and can be easily rinsed off.
CLEAN IT WITH A Q-TIP
Once you have let your nectar collectors soak for the allotted amount of time, take it out and rinse it a little with some warm water. If there are any areas that are not easily rinsing off, take a Q-tip and begin to scrub lightly to remove any difficult residue. It may take a couple of runs, but the residue will come off after enough soaking and scrubbing.
SOAK THE NECTAR COLLECTOR IN WARM WATER
Another method that you can use to clean your product is to place it in warm water and soap. The isopropyl alcohol and salt mix is great for stuck-on residue, but if you clean your dab straw frequently, you may not need to waste these materials on your piece. Instead, follow the same directions listed above and soak your device for as long as you see fit.
THOROUGHLY RINSE THE ENTIRE INSIDE
Rinsing the product will help to loosen any stuck-on residue before you scrub. However, it is important that you do so with hot water as cooler water may not be enough to get the desired effect. Hold your product under hot running water and even use the sprayer on your sink to get all of the nooks and crannies on your dab straw. This will help you identify which areas will actually need to be scrubbed once no more residue is washing off of the inside of your straw.
USE PIPE CLEANERS FOR TOUGH TO REACH SPOT
Is the Q-tip not doing the job for you. Don’t fret. Using a pipe cleaner can help you get the job done. Although it may be wide enough for certain areas, you may find that folding or twisting your pipe cleaner will improve its width so that it scrubs with ease. Once you have your pipe cleaner ready, carefully lower it into the body and push it back and forth, being careful so that you don’t rub the metal portion of the pipe cleaner against the body of your nectar collector.
LET IT DRY
After you’ve followed the directions above, do one final rinse of your product and take a look to make sure everything has been cleared from the inside of your nectar collector. Then, lay it out so that it dry, making sure that it is standing up so that the leftover water doesn’t pool on the side. If you’ve gotten every single piece of residue, your piece will be ready to use after it dries!
The BEST Marijuana Dispensary Near Me Scottsdale Deals. Top Shelf Scottsdale dispensary | Pick-up or Delivery. Edibles, Flower, Pre-Rolls, Vapes.
How Often Should I Clean It?
The answer to this question will depend upon how frequently you wish to clean it. Some people clean their devices regularly, which can help prevent hard residue from having the opportunity to serious build up in the first place. However, if you are someone who has a tendency to clean less frequently, the answer is that you should be cleaning your nectar collector at least every three to six months. Why? This is done to ensure that mold and bacteria don’t grow on the inside of your device, which could pose a threat to your overall health.
